Underground Fiber Optic Cables Monitor For Earthquakes?
Currently, researchers monitor earthquakes with seismometers,
which are more sensitive than the proposed telecom array, but
their coverage is sparse and they can be challenging and
expensive to install and maintain, especially in urban areas.
By contrast, a seismic observatory like the one Biondi proposes
would be relatively inexpensive to operate. “Every meter of
optical fiber in our network acts like a sensor and costs less
than a dollar to install,” Biondi says. “You will never be able
to create a network using conventional seismometers with that
kind of coverage, density, and price.”
But since the fiber optic seismic observatory began operation in
September 2016, it has recorded and cataloged more than 800
events, ranging from manmade events and small, barely felt local
temblors to powerful, deadly catastrophes like the recent
earthquakes that struck more than 2,000 miles away in Mexico. In
one particularly revealing experiment, the underground array
picked up signals from two small local earthquakes with
magnitudes of 1.6 and 1.8.
The fiber optic seismic observatory successfully detected the
8.2 magnitude earthquake that struck central Mexico on Sept. 8,
2017. (Credit: Siyuan Yuan/Stanford)
The fiber optic seismic observatory is just the first step
toward developing a Bay Area-wide seismic network, Biondi says,
and there are still many hurdles to overcome, such as
demonstrating that the array can operate on a city-wide scale.
The researchers will describe their findings in the journal The
Leading Edge in December. A paper focused on their signal
processing methods will appear in the January edition of IEEE
Signal Processing Magazine.
can read the preliminary announcement here in the Futurity
Newsletter. (FYI - if you like to follow technical and
scientific developments, the Futurity
Newsletter is published by a consortium of universities
to cover all topics of university research. It's simply great.)
Members And Instructors Working To Repair Hurricane Damage in
Houston, Florida and Puerto Rico
we showed photos from Houston, Texas showing the damage caused
by the recent hurricane. Of course that was followed by another
hurricane that destroyed part of the infrastructure in Florida
and Puerto Rico. We heard from some of our FOA contacts that
damage to the power grid control systems was massive and we were
told that in one case fiber cable was laid along the ground to
replace cable lost when towers were damaged, waiting for the
towers to be repaired. Our instructors have been working to
train new personnel needed for the massive amount of repair
Is This The End Of “Real”
Fiber Optic Standards In The US?
We just returned from a TIA
standards meeting, which as usual had a few surprises. During
the meeting, we realized we may be nearing the end of “real”
fiber optic standards in the US. It was predictable. In fact I
predicted it in 2009 when TIA announced that they were merging
the old FO-4 fiber optic standards committee into the TR-42
structured cabling committee.
The merger occurred because the FO committees which had been
meeting for over 25 years were losing steam. Most of the
important topics had been covered - component specifications had
been standardized and about 200 testing FOTPs (fiber optic test
procedures) had been written. Attendance was down, only 3 active
committees were left and no one asked (including yours truly)
was willing to assume the chairmanship. Since the FO committees
had been meeting at the same time and location with the TR-42
committees and TR-42 had ongoing work adding fiber to the
structured cabling standards, making fiber part of the TR-42
group seemed to make sense. Or did it?
When I heard the news, I sent emails to several members of both
committees expressing my concern. One of my sarcastic comments
was “Who decided a fiber optic technology group that covers
anything related to communications fiber optics gets stuffed
into a premises cabling group run by copperheads?” (JH email,
June 3, 2009)
I'm now saying "I told you so." Almost a decade later, at the
meeting in Las Vegas last month, I made the comment in one of
the subcommittee meetings that the document we were discussing
was an example of how TR-42 had recast fiber optic standards
into structured cabling standards, abandoning the general fiber
The first really important example of this was the adulteration
of OFSTP-14, the test standard for installed multimode cable
plants that I helped write in the late 1980s. The new version of
OFSTP-14 was adopted from an ISO document that was created as a
vehicle to require “encircled flux” mode conditioning in the
multimode standards. Rather than being about how to test the
cable plant, the majority of the new standard was about
encircled flux. You had to go all the way to the back to
Annex A to learn how to actually test a cable plant.
The updates of OFSTP-14 and more recently FOTP-171, many of the
fiber optic standards have been rewritten to support the latest
version of TIA-568. The older fibers that are still in wide use
like 62.5/125 (now called OM1) and the early 50/125 (OM2) are
not now recognized in these standards, confusing to many users
who still have these older fibers in use. We know because they
call FOA asking us questions. We tell them their systems are no
longer recognized by the current standards and they need to
refer to earlier versions that applied to them.
the US, I’d guess less than 5% of all fiber applications are in
structured cabling, probably only 50% of multimode. In the
committees, the majority of the attendees are from companies
specializing in structured cabling. So what’s happening is not
I’m still amazed by some of the stuff I see, especially coming
out of international committees. For example at the Las Vegas
meeting, an IEC document (IEC TR 61282-15) was presented to the
group purporting to cover testing multifiber MPO connectors.
Look at how this document defined a connector:
“connector - component consisting of two plugs mated together in
an adapter, for the purpose of providing frequent optical
interconnection/disconnection of optical fibres or cables,
between two cables, or a cable to an apparatus”
The rest of the world would call this a “connection” as the
committee agreed when I pointed it out. Perhaps it was "lost in
translation," but can anyone tell me how " two
plugs mated together in an adapter" connects to "an apparatus"
like a pluggable transceiver?
And then there is this definition:
“light source power meter - test system consisting of a light
source (LS), power meter (PM) and associated test cords used to
measure the attenuation of installed cable plant”
That’s also crazy - reference test cords (the ISO standards uses
the term cords instead of cables) are not considered part of the
There was more - the document used “back reflection” (an
obsolete, incorrect term), reflectance and return loss
interchangeably (often in the same paragraph) without defining
any of the three terms. And what it purported to cover, testing
MPOs, was incomplete and confusing. You are better off going to
the FOA Guide page on MPOs: http://www.thefoa.org/tech/ref/testing/test/test-MPO.html
which explains the issues in understandable language.
We know these standards are written by manufacturers for
manufacturers - we've been told that many times by TR-42 people.
What's a user/designer/contractor/installer to do? FOA responded
to this a few years ago, creating what we called 1-page
standards, simple explanations of the test methods with clear
drawings. Can a single page explain what is covered in a 30-40
page standard. Yes it can - check them out. FOA
Optics Used In Aerostat Tethers
Photonics has been known for its cables used in underwater ROVs
(remote operated vehicles) and we ran an article about one of
their cables used in Antarctica with a probe through a hole in
the ice. Now they have added a new application to their
protfolio, tethered balloons called Aerostats used for
surveillance and communications.
Linden is now leveraging its experience as a subsea cable
supplier and experience with light-weight, high strength
materials to service the airborne industry. These hybrid cables
have wires for power & fiber for data and are designed to be
durable for repeated use yet as light weight as possible for
maximum payload capacity.
Industries aerostat and Linden Photonics rugged, extra
strength cables used for tethers. Note the large amount of
strength members in the cable.
Is It April Fool's Already?
Or Is It " Fake News"?
We read this in an email
newsletter we get from CI&M magazine. You
can read the article here.
1) Can PoE provide the power? The lowest power normal PCs use
30-100W power and a 21" LCD display uses about 90W for 120-190W
total. A 21" iMac with the low res LCD uses about 75W but the
retina display versions uses 161W. Can these people convince PC
manufacturers to build such computers? Will companies buy then
instead of laptops?
2) Practically all workers today use laptops not desktop
computers. Typical users of desktops are power users doing
engineering or graphics on workstations that require really high
power. This idea could work for lapstops that use lower power, I
suppose because most are within the 90W limit. But most
modern laptops do not have a jack for Cat 5 - none of ours do!
3) Practically all of those laptops people use are connecting to
the network using WiFi or maybe cellular wireless.
4) Because of building codes, wherever a worker sits will have
Perhaps just another sign that the "Cat 5"community is really
grasping for something to do with all that copper wire in
warehouses! Just like the plan to run LED lighting off all those
too small conductors. All these proposals have also brought PoE
to the attention of the people writing electrical codes because
the high power heats up the cables sufficiently to be a
the article for yourself here.
Capacity Expands at OFS to Meet Global Demand
OFS owner Furukawa Electric plans to nearly double its 2016
optical fiber manufacturing capacity by 2019 and to increase its
optical fiber cable manufacturing capacity as well, thereby
creating over 400 jobs over the next two years. Between 2014 and
2016, Furukawa Electric increased its global fiber production
capacity by 20% and planned to achieve another capacity increase
of 20% by 2018.
“The proliferation of hyper-scale and edge data centers, 5G
wireless, and fiber-to-the-home (FTTH), along with the greater
digitization of communications in business, are creating the
need for fiber in the network around the world,” said Timothy F.
Murray, CEO of OFS. “Furukawa Electric is responding with
greater capacity as we foresee this demand continuing into the
next decade with communication traffic estimated to increase
during this period. Furukawa Electric will continue to serve its
global customer base and to contribute to growing communication
solutions in the market through a company-wide effort.”
Blog has lots of interesting stories - check out the one
on "rollable ribbon."
To Rent Dark Fiber? Nokia Will Sell You The Electronics To
Build Your Network
unveiled a line of optical transport platforms designed to meet
the needs of enterprises who want their own fiber-optic
networks. The portfolio aims to provide simple, low-cost
transport when paired with dark fiber.
According to Kyle Hollasch, director of product marketing,
optical networking, at Nokia, the growing interest in cloud
services and edge computing, as well as greater availability of
dark fiber, has piqued the interest of hospitals, banks, and
other large enterprises in managing their own optical
connectivity. Neither typical metro systems nor the new wave of
data center interconnect platforms quite meet such needs
adequately, Hollasch said, and therefore a new set of platforms
In addition to enterprises, Hollasch says Nokia expects to
generate interest in the WaveLite platforms among service
providers who want to offer private networks as a managed
service. In fact, initial WaveLite customers include a
communications services provider in Europe as well as a cable
operator and a Chinese internet content provider. He added the
company also is shipping systems to enterprises.
the story in Lightwave
Introduces Upgrades: LC SOCs - Splice-On Connectors
manufacturers of the EasySplicer have been supporting many of
the FOA schools with their fusion splicer. Our schools like
them because they are simple, easy to use rugged and reliable,
important for being used in the classroom or the field. The
company has just introduced an upgrade with some new features
and improvements including the availability of LC SOCs which
is important for data centers and high speed networks.
Upgrades include long life electrodes (5000 fuses) and a
higher temperature oven that can shrink SOC sleeves better. A
upgraded cleaver now includes a fiber trash bin to keep fiber
shards off the workbench. And software updates provide better
the new hardware is compatible with all EasySplicers in the
field now so you can easily upgrade.
For more information go
here (worldwide) or here
contact the manufacturer for your local EasySplicer
Publications Available From FOA
You Downloaded Your Copy Of The Updated
Fiber Optic Installation Standard Yet?
Free Courtesy of FOA
created to be a document that could be used as a guide to
installation practices and also be quoted in project paperwork
to define what was meant by installation in a "neat and
workmanlike manner." This standard was the first standard to
approach the issues of installation of fiber optics in a
document that could be used by network owners, project
managers, contractors, installers, test techs, maintenance
personnel and even the manufacturers making the products being
installed following this standard.
here for more information on NECA/FOA-301
and directions for a free download.
Latest Textbook - Fiber Optic Testing
Reference Guide To Fiber Optic Testing
of the FOA inquiries are about testing and most of those are
about OTDRs. Several interesting questions were asked this
first one deals with this event table:
This was sent to us by a tech testing cables at a job site
with an OTDR. The OTDR launch cable was ~150m. The cable being
tested had a number of fusion splices which you can see were
not reflective. The customer's spec for reflectance was -40dB,
so all the fusion splices passed. But the cable was rejected
because of the first event - that was the connection of the
launch cable to the OTDR.
The tech called us to help him explain to the customer that
the reflective joint at the OTDR had nothing to do with his
cable. We helped on that. But it brought up an interesting
topic - why did the OTDR manufacturer include that data
anyway? If you are using a launch cable, it has nothing to do
with the cable under test and is mostly just a confusion
factor. So we contacted the manufacturer. Their explanation
was it showed the condition of the connection at the OTDR and
when you see a high reflectance like this you can assume it
affects the dead zone of the OTDR. It also tells you to
inspect and clean this connection. We can see that, but it is
very confusing to someone who is not very familiar with OTDR
data. We could see it as a self-test mode, but not in every
data table. What do you think?
Several recent OTDRs we have tested have had SC-APC connectors
that greatly reduce the reflectance at the instrument
interface. We also recommend using a short cable to connect
the launch cable to the OTDR that stays on the OTDR all the
time. Not making that connection protects the OTDR interface
connector from excessive weer that affects both loss and
second one deals with OTDR setup:
We got this question in an email: What are good OTDR settings
for a 300-500m fibers? We’re using a 1.5 m launch cable and
sometimes got (-) loss.
answer was that a 1.5m cable is not a launch cable. A
launch cable must be long enough to allow the OTDR to settle
down after the test pulse. THe negative loss is because the
OTDR has not settled down sufficiently. Generally the minimum
launch cable for testing short cables would be 10-20m for MM,
100m for SM. Then use the shortest test pulse, ~1km range,
average enough to reduce the noise.
3 deals with distance:
We received a question about a VFL that would help identify
longer fibers, up to 10km long, and identify faults in the
cable. Our response was you need an OTDR. The high attenuation
of the fiber at visible light wavelengths (~650nm) makes it
impossible to use VFLs over 2-3km. Then we had to explain what
an OTDR was.
Number 4 deals with OTDR resolution and errors:
Finally, FOA Master Instructor Eric Pearson was doing some
comparison tests with several OTDRs for a new chapter in one
of his books. He made an interesting observation - the
variation in attenuation coefficient of fiber tested by an
OTDR was quite high on short fibers. His experiments showed
the variation was generally also sensitive to pulse width.
Think about how OTDRs measure attenuation:
If you are measuring a short length of fiber, say 100m, with
MM fiber, the loss is going to be ~0.3 dB, with SM ~0.04dB.
Depending on the OTDR range settings, the resolution of the
OTDR can become significantly large compared to the values
measured, causing digitiztion errors. Added to this, any
nonlinearity in the fiber trace caused for example by recovery
from the dead zone after a reflective connection - dependent
on pulse width - can have a very large effect on the
error of the measurement.
Think about it this way:
The variability on short length measurements can be explained
Attenuation coefficient = Loss / length
The uncertainty of the measurement is a combination of the
errors in each measurement
Attenuation coefficient = Loss+/-error <divided
Errors have both fixed components-same for all measurements -
and variable components-functions of the value being measured
For small values, fixed components tend to be more important
as they will become a larger percentage of the measured value
Dividing the two factors compounds the errors statistically
In fact, this is similar to measuring length with a ruler
calibrated in mm - you can only read to +/-1mm but that
resolution is more important when measuring 10mm than when
The FOA OTDR Simulator On Windows 10 or A Mac
If you want
to learn how an OTDR works or how to interpret traces, you would
ideally have an OTDR and lots of cable plants to test. That's
impractical for most users, but not for the FOA community. We
have collected tons of SOR (the industry standard for OTDRs)
files of OTDR traces and used them with a PC program for a OTDR
to create an OTDR simulator. You can open and compare traces of
one cable plant that show how the different choices in setup
(wavelength, range, pulse width, averaging, etc.) affect the
traces to understand how to make choices that optimize the
trace. Then you can open many traces from networks - very short
to very long - including traces through PON splitters and some
really graphic gainers!
The software has been set up long ago for Windows XP - we know
some of you still use it - and Windows 7 - same here - but one
of our instructors figured how to use a feature of Windows 10 to
make it useful on the latest versions of Windows. FOA
thanks Tim Fiegenbaum, Electronics Faculty & Coordinator,
North Seattle College for figuring this out and sharing it with
the FOA community.
For Using FOA OTDR Simulator On Windows 10
following link download the file: “Download the PC Simulator”
(Near the bottom of the page). http://www.thefoa.org/tech/ref/testing/OTDR/OTDRsimulator.html
Open the folder: “OTDR Win 7” …unzip
If using Windows 7 or XP, simply install the file:
If using Windows 10
Right click on the file: Setup_uOTDR_V9x.exe and select
Select the "Compatibility" tab and select the option for
Click apply and then OK
Click on the file "Setup_uOTDR_V9x.exe” and follow the direction
Open the file "uOTDR.exe" to run the program
The program will run just fine in Windows 10 if the Windows 7
compatibility mode is selected.
Some anti-virus software including Norton 360 will
identity Setup_uOTDR_V9x.exe an unsafe and will quarantine
the file. If that happens you will need to un-quarantine
the file in order to install.
For Using FOA OTDR Simulator On A Mac
the OTDR Sim on a Mac is easy. There are several Windows
emulators available for the Mac including Apple's own
BootCamp, Parallels Desktop, Crossover, WinOnX, Virtual PC and
VMware Fusion. We run our OTDR Sim on a Macbook Air using
Fiber Optic Installation Standard
Free Courtesy of FOA
The ANSI/NECA/FOA-301-2016 standard for Installing and Testing
Fiber Optics has been updated and is available for download from
the FOA website. This standard is one of the many volumes in the
NECA (National Electrical Contractors Association) NEIS series
(National Electrical Installation Standards). FOA and NECA
created this standard in 2001 and this is the 3rd revision.
created to be a document that could be used as a guide to
installation practices and also be quoted in project paperwork
to define what was meant by installation in a "neat and
workmanlike manner." This standard was the first standard to
approach the issues of installation of fiber optics in a
document that could be used by network owners, project managers,
contractors, installers, test techs, maintenance personnel and
even the manufacturers making the products being installed
following this standard.
Download Free From FOA
As the authors of NECA/FOA-301, FOA feels strongly that this is
a standard that every fiber optic tech - designer, installer,
tester - as well as network owners should have for reference.
Therefore, FOA sponsors distribution of this standard free to
those involved in fiber optic projects. We encourage you to
download a free PDF copy and tell others to do so themselves.
here for more information on NECA/FOA-301
and directions for a free download.
de Diseño para Redes de Fibra Óptica en
Español - FOA
Design Book Available In Spanish - Online
FOA has translated the FOA Guide To Fiber
Optic Network Design book and made it available online to
those studying for the CFOS/D Certification but whose native
language is Spanish. You
can access the Spanish translation of the Design book here.
A printed version will be available in the near future.
Newest Textbook - Fiber Optic Testing
has published another "reference guide" textbook: FOA
Reference Guide To Fiber Optic Testing. This is
a new textbook for training or studying for FOA CFOS/T
certifications, and an up-to-date reference on fiber optic
testing for the contractor, installer, designer and user.
Fiber optic manufacturers and network users say that testing
is the most important aspect of installation and operation of
fiber optic networks but often the least well understood. Of
all the technical help requests received by the FOA, 90% are
about testing. This book has been written by the FOA to
provide a comprehensive but understandable technical guide to
this important topic.
The FOA Reference Guide To Fiber Optic Testing is a unique
book. It covers the topic of fiber optic testing more
thoroughly than this topic has ever been covered in a
textbook before and in some different ways. Every subject
(see Table of Contents below) starts with basic
information on why a test is necessary and what test
equipment is required which everyone needs to know. Then
the chapter expands on how the tests are performed and
completes the topic by discussing the potential
measurement uncertainty and how to minimize that
Several chapters are at the expert level. Chapter 10 on
fiber characterization is technically complex but a
subject that is becoming more important for upgrades to
older cable plants and new installations intended for 100G
and beyond. Chapter 14 on Metrology - the science of
measurements - is the longest and most difficult chapter
to master. This chapter is aimed at the experienced tech
who wants to understand the depths of fiber optic testing
and use that information to make their testing more
accurate and usually much faster.
($9.95 on Kindle)
7" x 10" (17.78
x 25.4 cm)
Reference Guide To Fiber Optic Testing
YouTube Videos Now "Closed Captioned"
YouTube videos are very popular as you can see from the
statistics above. We have had requests from teachers and viewers
for closed-captioning. Now FOA is upgrading all its YouTube
Videos to offer "closed captioning" for those with hearing
disabilities - or if you want to view the video quietly and
don't have headphones. FOA used a highly-regarded service that
does closed-captioning for many of the television networks to
ensure accurate captioning.
The closed captioning can be turned on by the small "CC" button
on the lower right side of the video (right arrow). The
captioning shows up on screen in white letters on a black
background (left arrow). You can view
this video on fiber optic testing here, and try the "CC"
button to see how it works.
We hope our viewers find this helpful.
FOA has over 100 YouTube videos on fiber optics, premises
cabling and the fiber optic job marketplace. Here
is a list with links to them online.
Website Keeps You Up To Date On Structured Cabling
Goldsmith, manager of the TIA Fiber Optic Technology Consortium
(FOTC) has started a new website that aims to keep readers up to
data on the news and products in the structured cabling
(premises cabling) space. Called Structured
Cabling News, it offers news about the industry in more
than a dozen categories so you can browse the news by categories
(like fiber) that interest you most. Liz sums up the aim of SCN
as "SCN brings you current Structured Cabling News curated by
category and topic. We search the 'Net so you don't have to -
updated daily with industry trends, new products and best
practice from industry leaders."
And you can subscribe to daily or weekly digests to keep
In A Career In Fiber Optics?
FOA has created a new YouTube video to introduce students to
careers in fiber optics. It was made for showing to high school
and junior high students interested in tech careers but anyone
interested in a possible career in this field will find it
interesting. If you have kids in school or know teachers, let
them know about this too. Watch the FOA
Careers In Fiber Optics Video on YouTube and visit the FOA
Careers In Fiber Optics web page at www.foa.org/careers/.
Forrest - NEW Lecture On Cleaning And Inspecting
Forrest, the person we consider the guru of cleaning fiber
optic connectors, has added a video lecture on cleaning. It's
a bit long for YouTube, about an hour, but worth every minute
Way To View Fiber Optic Connectors
are used for inspecting connectors for two primary purposes,
checking polished ferrules during termination to ensure proper
end finish and checking connectors in the field to determine if
they are clean. To date, one type of microscope has been used
for both operations, but a new tool from a long time industry
expert may change some minds. To inspect polish quality, you
need high magnification, typically 100 to 400X, with most users
preferring the higher magnification. But if you inspect for dirt
at that magnification, you can only see the ferrule end,
ignoring the rest of the connector which can be filthy and you
will never see it.
Ed Forrest, the "guru of cleaning" has come up with a very
useful tool. Ed is well known for his website on cleaning and
his books (go to http://fiberopticprecisioncleaning.com/)
and has now added a product for inspecting connectors for
cleanliness. Instead of a standard microscope, the RMS-1
Fiber Optic Inspector uses a zoom microscope attached to a
PC with unique 3D-printed adapters to hold connectors. You get a
wide angle view that can show you how clean the connector is
really. The biggest advantage is its ability to see the whole
MPO connector or into the shell of large multi-fiber connectors
like the MIL-38999.
Looking inside a SC connector with the RMS-1
You have probably never seen a MPO connector in this way before
More views of SC, LC and MPO connectors
Here is the datasheet
on the RMS-1 Fiber Optic Video Scope
This product is different than other microscopes in many ways.
It attaches to a PC or Netbook. The 3D printed adapters take
some getting used to, but the results are reallu useful. Ed is
still in the development phase, so there is no website yet. Here
is his email if you want more information: firstname.lastname@example.org
Underground Utilities - An Overview of Methods
In searching for articles on underground utility location
regarding the problems caused by contractors digging up
cables and breaking water pipes, we found this
interesting summary of methods of location. It
includes electromagnetic, acoustic and radar methods, plus
one we did not expect - dowsing. Dowsing is a technique for
searching for underground water, minerals, or anything
invisible, by a person carrying an indicator, traditionally
a forked stick, now often paired bent wires, pointing
downward toward whatever they are searching for supposedly
in response to unseen influences.
We suggest more modern technical methods of searching for
buried utilities, but whatever you do, use the resources
available before you start digging! Read
the FOA Tech Topic. There is a toll-free "call before you
dig" number in the USA: 811. See www.call811.com
for more information or go to National
Fiber Optic Protection Summit by the "811" group. The
US Department of Transportation has a website called "National
Pipeline Mapping System" that allows one to search for
if anyone really has experience with dowsing, tell us about
and Certification In California
California, PG&E (Pacific Gas & Electric) has created
a program for training and certification for avoiding
underground utilities called "Gold
Shovel Standard." PG&E developed the Gold Shovel
Standard Certification process to ensure that PG&E's hired
contractors adhere to the safest excavation standards.
Viavi Database Illustrates More Than 500 Operational or
Planned Deployments Of Gigabit Broadband Globally
Communications service providers worldwide are accelerating
efforts to deliver gigabit internet -- network speed that is 159
times faster than the global average of 6.3 Mbps. The Gigabit
Monitor, a visual database referencing current and planned
gigabit deployments around the world, from Viavi Solutions (the
test equipement company formerly known as JDSU). The Gigabit
Monitor paints a picture of mobile, cable and telecom service
providers all racing to deliver lightning-fast internet
connectivity to meet end users' demands. The database, developed
completely from public information, is available at: http://www.gigabitmonitor.com.
Below are some of the key insights from the Gigabit Monitor:
of gigabit: There are now at least 350 live gigabit
deployments globally, with a further 164 announced or under
construction, across wireline and wireless technologies
including GPON, DOCSIS 3.1, G.fast, LTE-A, 5G and 802.11ac.
by region: North America has the largest share of announced
gigabit deployments, with 61 percent. Europe is second with
24 percent. Asia, Australasia, Middle East, Africa and South
America share the remaining 15 percent of deployments.
accelerate: The pace of gigabit deployments has accelerated
sharply. Over 70 percent of the live gigabit deployments
tracked have been launched since the start of 2015.
dominates: 85 percent of currently known gigabit deployments
are based on optical fiber connectivity. 11 percent are
based on Hybrid-fiber coax (HFC), a broadband technology
that combines optical fiber and coaxial cable, commonly
employed by cable providers.
gigabit is already here: Nearly 3 percent of known gigabit
deployments are based on LTE-A, a modified version of LTE
which is gigabit-capable.
- 5G is
coming fast: 37 wireless carriers have announced plans for
5G networks. Five of them plan to have 5G networks built as
early as 2017.
The word on
the "Dig Once" program is getting out - FOA is getting calls
from cities asking us for information and advice. It helps that
the current Administration is trying to convince cities of the
advantages of installing ducts or conduits when they dig up a
street so they don't have to do it again. Here are some links
for more information.
The DoT page on the administration’s Executive Order: http://www.fhwa.dot.gov/policy/otps/exeorder.cfm
From the Council of State governments: http://www.csg.org/pubs/capitolideas/enews/cs41_1.aspx
From the city of San Francisco: http://sfgov.org/dt/dig-once
An article about Dakota County, MN: https://muninetworks.org/tags/tags/dig-once
the one to download and hand out:
A “How To” Guide from The Global Connect Initiative: https://share.america.gov/wp-content/uploads/2016/04/6.-GCI-Dig-Once.pdf
have contacts give us online links for useful information which
we like to share with our readers. Here are two:
Learn More About DIY FTTH?
Fiberworx is a DIY FTTH Project in Georgia
like every week FOA gets another call from a town, real estate
developer or utility wanting to start a FTTH project for their
area. FOA has created several videos and a a web page on this
topic to help anyone get started.
Case Studies: Do-It-Yourself FTTH
FOA has a
series of videos on do it yourself (DIY) FTTH. The first three
videos are online now:
Lecture 45 Do It Yourself FTTH (Fiber to the Home) What's
involved in building a FTTH network of your own.
Lecture 46 Do It Yourself FTTH (Southern Fiberworx)
November 2015) How one company, Southern Fiberworx in
Cordele, GA did it themselves.
Lecture 46 Do It Yourself FTTH (Southern Fiberworx)
We Warn You To Be Careful About Fiber Shards
Photo courtesy Brian Brandstetter, Mississauga
Source Of Articles On Fiber
President and editor of this newsletter Jim Hayes has also been
writing a column in Electrical
Contractor Magazine for more than 15 years now. Electrical
contractors do lots of fiber work and this column has covered
some toics they are interested in including installation
processes, network design, fiber applications and in the last
year, a lengthy series on dark fiber - what it is, how's its
used and how it benefits the growth of communication. A recent
web site redesign makes it easier to browse all these articles -
just go to http://www.ecmag.com/contributing-authors/jim-hayes
and you can see all of them.
Optic Education For Students At Any Age
about fiber optics all the time - it's in the news whenever we
hear articles about high tech, the Internet and communications,
and many communities are getting "fiber to the home." But few
people really understand fiber optics or how it works. FOA is
focused on educating the workforce that installs and operates
these fiber optic networks but we're always getting inquiries
from STEM (science, technology, engineering and math) teachers
who want to introduce fiber optics to younger students in K-12
grades or technical schools.
start with the FOA
Careers In Fiber Optics Video on YouTube and visit the FOA
Careers In Fiber Optics web page at www.foa.org/careers/.
These are for students who think they might be interested in
careers in fiber optics and want to know more about what fiber
Using red laser light (a VFL here but a laser pointer works
also) to show how fiber guides light.
FOA has begun developing a series of YouTube videos intended for
teaching students in elementary, middle and high schools about
fiber optics. The first FOA video is titled "Fiber
Optics For Teachers." With this video, we show teachers
how fiber works and carries signals and then explains simple
experiments to demonstrate how fiber optics works in the
classroom using some plastic fiber and a laser pointer. Since
many teachers do not know where to get the fiber, the FOA offers
to send them a sample for use in demonstrations in their
classroom (USA only right now.)
At the end of the video, teachers are given directions on how to
request samples of the plastic fiber from the FOA.
This video joins the "Fiber Optics Live" series How
Light Travels In A Fiber, Fiber
Attenuation and Connector
Loss that show how fiber works using simple experiments
that can be duplicated in any classroom. More videos will be
If you have kids or know some teachers who would be interested,
please send them to the introductory video Fiber
Optics For Teachers and we'll be glad to help them
get started with some entertaining programs for their
For Teachers In K-12 And Technical Schools
Teachers in all grades can introduce their students to fiber
optic technology with some simple demonstrations. FOA has
created a page for STEM or STEAM (science, technology,
and math) teachers with materials appropriate to their
classes. Fiber Optic
Resources For Teachers.
you have kids in school or know teachers who are interested,
send them to the FOA page Fiber
Optic Resources For Teachers.
Your Company Become An FOA Corporate Member?
As all FOA
members know, they join the FOA by becoming certified,
mostly taking their CFOTs but some CPCTs, either by
attending a FOA approved school or joining directly based on
field experience (our "work to cert" program.) Over the years,
we've been contacted by manufacturers, contractors, consultants,
and other types of organizations who ask about becoming members.
We don't certify companies or organizations, we told them, so we
were not sure what we could offer as a benefit of membership.
But then, companies asked about using our educational programs
to train employees, how they could get listed on the FOA website
as service providers or if they could get a quantity discount on
membership or certification for all the FOA members working for
them. That began to sound like a benefit for being an FOA
corporate member. And providing a list of useful suppliers to
the market could be a benefit to the industry as a whole.
So FOA has quietly been letting companies and other
organizations join the FOA to take advantage of those benefits
so we now have several hundred corporate members. We've put then
into a database and listed them on the FOA website in map
form. Here's the map.
The online map
can be used to find suppliers and service providers.
The map, like our map of schools, lets you find the FOA
corporate members close to you. The table form lists them
by category: Installer/Contractor, Component Manufacturer,
Installation Equip. Manufacturer, Transmission Equipment,
Services/Consulting, Distribution and Users of Fiber Optic
Networks. You can sort the tables to find members meeting your
needs, e.g. by location, certifications offered, etc. Click on
any column heading to sort that column; click twice to sort in
Does An Organization Become An FOA Corporate Member?
just fill in the online
application form. When your application is accepted, you
will be asked to pay the membership fee - $100US first
year, $50US/year or $100US/3years to renew. You will then be
listed on the online
have access to exclusive FOA educational materials for your
employees and get discounts on certifications and
On The Job
the most important part of any job. Installers need to
understand the safety issues to be safe. An excellent guide to
analyzing job hazards is from OSHA, the US Occupational Safety
and Health Administration. Here
is a link to their guide for job hazard analysis.
FOA also has lots of information on safety: FOA
video and a Safety
Reading" Is Now On
FOA on Pinterest.
We have been posting links to pages "Worth
Reading" on a special FOA Pinterest page. You can join and
keep up to date with the news on our industry which we put
posts cover utilities using new generation telecom, India's
plan for 100 smart cities, Cincinnati Bell bets on fiber,
various opinions on the US battle over net neutrality, etc.
Practice Tools For OTDRs, All Free
may already know that the FOA has a free OTDR Simulator you can
download from our website (go
here for directions) that allows you to practice using an
OTDR on your PC (Win XP or 7), seeing the effects of changing
setup parameters and analyzing dozens of real world traces. But
here are two more tools that can be good for practice.
more hints from FOA Master Instructor Terry O'Malley like tests
on what the end of a fiber trace looks like with broken and
Asked Questions On OTDRS And Hints On Their Use
APP Reads, Analyzes OTDR Traces
is a iPhone/iPad APP that reads industry-standard ".sor" format
files and allows trace analysis on your iPhone or iPad. An
android version is in the works too. Read
more about Fiberizer. And
here are more directions on its use.
now posts events on our LinkedIn groups, Facebook page and
other social media
has a company page and three LinkedIn Groups
- official company page on LinkedIn
- covers FOA, technology and jobs in the fiber optic marketplace
Fiber Optic Training - open to all, covers fiber optic
technology and training topics
de La Asociación de Fibra Óptica FOA (Español)
Happening @ FOA
FOA now offers free standards for datalinks and testing the
installed fiber optic cable plant, patchcords and cable, optical
power from transmitters or at receivers and OTDR testing. Look
for the "1
PageStandard" web page and in the FOA Online Reference
301 Fiber Optic Installation Standard
cover components and systems and how to test them, but rarely
get into installation issues. The FOA NECA 301 standard which
covers installation of optical fiber systems has been revised
for the second time, adding considerable new materials. This
standard is derived from FOA educational material put in
standards form and approved by ANSI as an American National
Standard. It's specifically written to be used in contracts to
define "installation in a neat and workmanlike manner." The
standard is available from NECA.
FOA members can go
here for instructions on how to download your free copy.
Fiber U Self-Study Programs
"Fiber U" free online self-study programs help you learn about
fiber optics, study for FOA certifications or use them to help
create "blended learning" classes. There are two new free online
self-study programs on Fiber
U. Fiber Optic Network Design is for those interested in
learning more about how to design fiber optic networks or
studying for the CFOS/D certification. FTTx is for those wanting
to know more about fiber to the "x" - curb, home, wireless, etc.
- or studying for the CFOS/H certification.
Got to Fiber U
for more information.
Online Self-Study Programs Offer Certificates of Completion
been offering quite a few free online self-study programs on Fiber
U, our online learning site. We are always getting
questions about getting a certificate for completing the course
online, so we have setup an option to take a test online and get
a certificate of completion for these online courses.
While it's not FOA certification, FOA will recognize a Fiber
U Certificate of Completion as background experience to
qualify for applying for FOA certifications. We also intend to
expand the program to more specialized topics as preparation
for FOA specialist certifications.
If you have associates that want to get started in fiber,
have them take this course online to get started. Go to Fiber
U and get started.
& Uncle Ted Guides - Perfect For Getting Started
Ted's Guides have moved to the FOA website.
Lennie is the place where many if not most fiber techs
begin their education. FOA has just updated the two
guides to ensure they stay relevant - more than 20 years
after they were first written.
Lennie goes all the way back to 1993 when he was created
as the mascot of the original "Fiber U" conference - the
same Fiber U that is now the FOA's web-based training
Lightwave's Guide To Fiber Optics was created
as a beginner's introduction to fiber optics. Over
60,000 printed version of Lennie's Guide were given away
and it became one of the first commercial web pages in
1994. Uncle Ted's
Guide To Communications Cabling was written a
few years later to introduce techs to "Cat 5" - UTP
wiring - that had only recently been standardized in
Lennie and Ted's Guides are used in the current Fiber U
online self-study programs and are still the best place
to start learning about fiber optics.
Ted's Guides are online at the links here, can be
downloaded as printable PDFs and are now also available
as free iBooks on iTunes.
Lightwave's Guide to Fiber Optics and
Ted's Guide To Communications Cabling
are now available free to iPad users who can download them from
the Apple iTunes store. Of course they are still available
online or for download.
You can also find these free guides on the FOA website - go here
for all the links: Lennie
Lightwave's Guide to Fiber Optics and Uncle
Ted's Guide To Communications Cabling
Reference Guide To Fiber Optic Testing
Basic Fiber Optic Textbook Now Also Available in French
Reference Guide To Fiber Optic Network Design And FOA's
Outside Plant Fiber Optic Construction Guide
More about the FOA
Reference Guide To Fiber Optic Network Design
information on the FOA
Outside Plant Fiber Optics Construction Guide
LossCalc estimates the optical loss of a fiber optic link. This
will save time for the installer of a fiber optic link needing
to know whether test results are reasonable and/or make a
"pass/fail" determination. It can also help the designer of a
link to determine if communications equipment will operate over
By choosing the type of link (singlemode or multimode) and
specifying the length of the fiber and numbers of connections
and splices, it will calculate the end to end loss of the link.
The app has default specifications for singlemode and multimode
links or the user may create custom setups with specifications
appropriate for any application. http://itunes.apple.com/us/app/foa-losscalc/id476262894?mt=8&ls=1
Self -Study in Fiber Optics
first app is a self-study version of the FOA Reference Guide to
Fiber Optics. The FOA APP builds on the FOA basic fiber optic
textbook to create an interactive learning environment that
builds on the iBook electronic version of the book to add a
guide to use for self-study and real-time testing that provides
feedback on what you have learned and correct answers to
questions answered incorrectly.
The FOA APP is priced at only $9.99, same as the iBook, so the
self-study program is free. Download it from the Apple APP Store
with your iPad or iTunes.
FOA has many videos on ,
including two Lecture Series (Fiber Optics and Premises
Cabling), Hands-On lectures on both and some other informational
and instructional videos. For all the videos, go
to the FOA Channel "thefoainc" or use the direct links
a complete list of FOA Videos with links to each video on
The Jobs In Fiber Optics? FOA talks about all the
applications for fiber optics, what jobs involve and the
qualifications for the workers in the field.
Optics - Live! A
series of videos that use lab demonstrations to show how
optical fiber works.
Project Management - what's involved in a
copper/fiber/wireless project -advice for the customer and the
Of Counterfeit Cable
have read the stories we have written about the counterfeit
"Cat 5" cable made from copper-clad aluminum rather than pure
copper. Recently we tried an unscientific burn test on the
cable compared to a known good UL tested cable and posted a
video on YouTube. You can see the results below.
Cable Real UL-rated cable
difference is obvious and the danger is real. Watch the video
on YouTube: Premises
Cabling Lecture 11: Counterfeit Cat 5 Cabling
complete list of FOA Videos with links to each video on
all the FOA Channel on YouTube.
New in the FOA Online Fiber Optic Reference Guide?
continually updating the Online Reference Guide to keep up with
changes in the industry and adding lots of new pages of
technical information. Go to the FOA
Guide Table of Contents to see the latest updates - look
What You Want Using "Google Custom Search
so much information on the FOA Tech Topics and Online Fiber
Optic Reference Guide that even a well-organized Table of
Contents isn't enough and when the material is always changing,
an index is impossible to maintain. So the FOA is using the
latest technology in search, Google Custom Search, which will
allow you to search just the FOA Tech Topics and
Online Fiber Optic Reference Guide for any topic you want to
find more about. Try
FOA Online Fiber Optic Reference Guide.
The FOA welcomes the newest additions to our listing of FOA-Approved
The FOA network of training
organizations offering CFOT (and more) certifications continues
to expand. We welcome six new schools from quite different
backgrounds - a manufacturer, an electrical JATC and several
Tellabs Training Services,
Dallas TX school #363
Rally Training Services, Genola,
UT, USA #364
Mundo Interconnect LLC,
Mansfield, MA USA #365 (teaching in Ecuador)
Springfield Electrical JATC,
Springfield MA school #653
Optic Training Toronto, Toronto, ON, Canada #366
Van Tek Consulting, Queen Creek, AZ, #367
a listing of all the FOA-Approved schools here.
An FOA-Approved Training Organization
inquiries we get regarding finding a FOA-Approved training
organization want to know two things: what school is closest to
me or what school offers the certifications I need. The FOA has
about 200 training organizations we have approved worldwide so
finding the right one can be difficult! We've been looking at
ways to make it easier, and we think we've got a good solution.
In fact we have two solutions.
First we have added a sortable
table of all the FOA-Approved schools.
You can also use our FOA
Google Map to find FOA-Approved schools.
Should A Fiber Optics or Cabling Tech Know and What Skills Do
certifications are based on our KSAs - the Knowledge, Skills and
Abilities that techs need to succeed. Read the FOA KSAs
for fiber and cabling techs.
enjoy feedback, especially when it shows how great some FOA
instructors are. These came from students of Tom Rauch, an
instructor at BDI
"I took your fiber optics certification courses this past March.
I just wanted to let you know that in two weeks I start working
as a fiber optic technician with ___ up in ___. You mentioned on
the first day of the course that there is always one guy in
class who had rubbed his last two nickels together to be there
and, in that instance, I was that guy. Now I'm going to be able
to provide for my family like never before and I owe it to the
certification that I received from you and BDI Datalynk. I just
wanted to thank you again."
"Thanks to our tremendously knowledgeable and patient instructor
Thomas Rauch, who was not only generous in sharing his wealth of
information, but he did so with ease, humor and in a way that
invited curiosity and participation. He was encouraging and
proud of our accomplishments and helped us learn from our
mistakes in a way that did not break our confidence, rather it
pushed us to better results the next go around. The hands on
labs were just AWESOME!" Just thought you should know what a
class act you have representing you in his travels..... but then
again you probably already knew that! : )
In almost 19 years at Verizon and having held numerous
positions, I have gone through many training sessions. I cannot
remember ever having been actually looking forward to coming
back to class quickly after lunch, to get back to the hands on
activities, and walking away with the sense of empowerment that
the information presented was not only relevant but dead on
point accurate! I will be signing up for the Outside Plant class
on March! I can't say enough good things about Tom and his
impact! Feel free to quote me, I can only imagine that he will
open so many doors and change so many lives in the years to
come, with his style of teaching! Great experience, awesome job!"
and FOA Partner on Fiber Optic Training
International Brotherhood of Electrical Workers (IBEW) and the
National Electrical Contractors Association(NECA) through the
National Joint Apprenticeship and Training Committee
a partnership with the FOA has published a new textbook for
training IBEW apprentices and journeymen in fiber optics. The
new textbook uses the material from the FOA Reference Guide To
Fiber Optics with new material and photos from other NJATC
from one of our certified instructors: I want to thank
you and your organization for all the resources you provide for
the students and the opportunity to offer the certification to
the students. The fact that you published the book yourself to
get the cost down and the unlimited free resources on your
website shows a commitment to the public that is second to none.
I let it be known to the students that the FOA is the best in
the industry at supplying knowledge and resources related to the
communication industry. I look forward to passing on the
information that you provide for the industry.
Question! Tech Questions/Comments Worth Repeating
Questions From FOA Newsletter Readers
Q: I have taught for several institutions and throughout
all my years of doing this I was always taught that when testing
for insertion loss and back reflection for singlemode cable
links that testing bi-directional is an imperative.
Recently when I was attending a meeting involving members of the
military along with folks involved in the development of the
military manuals, it was mentioned that with singlemode testing
that bi-directional testing is not necessary.
A; First of all, there is a directional difference in
splice or connector loss - and maybe reflectance (that term is
now almost universally used in place of “back reflectance” which
is a poor term since a reflection is always back) - as long as
two different fibers are being spliced. Fiber geometry is the
main difference - mode field diameter in SM and core diameter in
MM - but it can also be a matter of the fiber composition.This
happens if two different manufacturers’ fibers are joined or
bend-insensitive (BI) fiber with differences in depresssed
cladding geometry are joined.
If you test bidirectionally with sufficient accuracy, you can
see the difference. It’s an OTDR trace that most people are
familiar with - if you see a gainer, you shoot the
other direction and average to get the “actual” splice loss.
When splicing or connecting different types or manufacturers SM
fiber you may see directional differences of up to 0.3dB or
more. Same for MM, not only for differences in core diameter but
also for connecting BI to non-BI fibers. While those OTDR
measurements are actually differences in backscatter levels,
they are indicative of real differences in connector loss or
splice loss in opposite directions.
Are those differences enough to be of concern? That’s a judgment
We’ve found most people do their bidirectional testing all
wrong. With an OTDR, you should disconnect the instrument, not
your launch and receive cables, and take just the instrument to
the other end. Disconnecting the launch and receive cables
changes the fibers at the connections to the cable under test
and you lose the connection you want to test from the opposite
Bidirectional testing with a test source and power meter is more
confusing. You have to do your “0 dB” reference, check the
launch and receive reference cables, measure the cable under
test, then move just the source and meter to the other end, test
the cable under test again, then disconnect and then measure the
output of the source to get the “0 dB” reference used in that
direction. That’s confusing!
Even if you do test bidirectionally, you do not get the “actual”
connection or splice loss like everybody says - you get the
average of the two directions. Unless you are willing to do a
lab setup and some careful testing, that’s the best you can do.
Now we are into measurement uncertainty. If the measurement
uncertainty is around the same as the typical bidirectional
difference, does bidirectional testing gain you that much?
That’s a judgement call.
The new FOA book on
testing goes into this - a complete chapter is devoted to
When To Test Fiber
Q: Should testing of the fiber plant be done before the
Optical Network Terminal is installed?
A: Fiber optic testing is generally done when the cable
plant is installed to confirm proper installation and check that
the performance is adquate for the electronics planned for use
There are several processes - first an overview of testing:
Check cable before installing - continuity if it looks OK, OTDR
testing if the reel is damages
Test installed cable when splicing - check the fusion splicer
estimate of loss and do OTDR testing if questionable and inspect
every connector as termination is done to confirm the connector
Test cable plant after splicing and termination - end-to-end
insertion loss and OTDR testing for longer OSP (outside plant)
New singlemode cable plants for high speeds may need "fiber
characterization” - adding in CD (chromatic dispersion), PMD
(polarization mode dispersion) and SA (spectral attenuation for
DWDM wavelengths) testing. If one is considering upgrading a
cable plant that is already installed or has been used, these
same tests should be done - inspection/cleaning, insertion loss,
When the system is installed, one should know it should work
because of the testing done during installation. One should
inspect and clean patchcords before installation and test them
if suspect. In fact any connector needs inspection/cleaning
before hooking up equipment. Dirt is the biggest problem with
fiber optic systems.
Between Singlemode or Multimode Mating Adapters
Q: What is the difference between singlemode and multimode
bulkhead/adapters (mating adapters). My understanding is you
cannot use the singlemode with the multimode and visa versa.
A: There are 3 types of adapters - rated for SM or MM -
based on the alignment sleeve material.
-Plastic (glass filled thermoplastic) alignment sleeves are
cheap, not very precise and wear quickly (you can see ceramic
ferrules get dirty using them) - only good for multimode and one
or two insertions - not recommended
-Metal (phosphor bronze) alignment sleeves are better with good
alignment but still wear some - OK for MM, some are rated for
singlemode (check before you buy), and are OK for most uses but
will wear out if used for repetitive testing
-Ceramic alignment sleeves are the best and most expensive. They
are very precise in alignment and last for a long time.
Recommended for all singlemode and all testing purposes.
Don’t use MM adapters for SM but SM adapters are OK for MM.
Why A Figure 8?
Q: What is the reason for wrapping the cable in a figure
A: When you need to do an intermediate pull, you have to
pull the fiber and coil it on the ground. A simple coil will put
a twist in the cable. Figure-8 coils put in twists of opposite
directions on each side of the 8 making for no overall twist in
the cable. See How
To "Figure 8" Cable For Intermediate Pulls in the FOA
Can I Build A GPON Network With "Taps"?
Q: Can I build a GPON network where I do a drop to one
subscriber then continue to the next subscriber for another drop
and so on?
A: There have been examples of this type of “tap” drop proposed,
for example in rural areas for drops to widespread
subscribers on a longer network than is typical for FTTH. It’s
just a version of a cascaded splitter network. with taps that
just do a 2 way split. The taps used are typically 90/10 taps,
where 10% of the power is tapped off for the drop.
There are some important issues to consider - Since you are
dropping 10% of the power at each tap, you are limited by how
many drops you can have. If you calculate the loss
budget - after the first tap, you have 90% power left less the
excess loss of the splitter (~0.3-0.5dB). The tap power is down
~10.3 dB and the through power is down ~0.6 dB. At the next tap,
you use the same formula plus you add the loss of the
fiber to that tap and so on until you reach the GPON
limit. It’s a pretty complicated process to design, but
you can see that with these power losses you will not get a
large number of drops in a GPON network with 28dB max power
budget. We did a rough calculation and 20-24 drops may be
possible depending on the fiber lengths.
This network will probably be much more expensive and more
distance limited than simply running a cable with many fibers
and dropping fibers from that cable with midspan entry. Couplers
are expensive, fiber is cheap. We also do not know the issues
with the large differences in transmission times between the
first connections and the last ones, which depends on the length
of fiber in the systems. That may require some programming at
OM1 MM Fiber
Q: We are an automation system integrator in South Africa. We
have a client that has multimode 62.5/125 fibre optic plant
wide. None of the runs between components are longer than 2km.
We intend to upgrade the technology from a proprietary
communication protocol to a standard ethernet protocol at 100
MHZ. The fibre to copper convertors we will be using are using
1300nm light source and have a Fibre Optic Link Budget of 12.8dB
for 62.5/125 um and 9.8dB for 50/125 um. The client has been
advised to replace the multimode 62.5/125 with multimode 50/125
cabling and we need to know if this is really a requirement.
A: Do you know how old the fiber is? It should be what we called
FDDI grade 62.5/125 fiber with a loss of ~1dB/km and a bandwidth
of 500MHz-km at 1300nm. A 2km link should have a loss of 2dB for
the fiber and ~0.5dB/connection - well under the power budget of
the link. 100Mb/s Ethernet variants were designed for 2km or
more on this fiber. There is no reason to upgrade at this time,
50/125 fiber would not be needed until Gigabit Ethernet was
Do We Need Repeaters For 30 Mile Link?
Q: I need to design a 30 mile (~50km) link. Will regeneration
like a fiber amplifier be necessary?
A: It depends on the comms equipment but I doubt you need
regeneration. 30 miles is 50km, only 10dB of loss for the fiber
at 1550nm, maybe 10 splices at <0.1dB adds only 1dB loss and
another dB for connectors on each end. I think you probably can
find equipment that runs on 12dB loss budget. That said, most
new high speed systems (>10G) have 20km versions then go to
expensive long haul coherent systems. So talk to the
communications equipment manufacturers and see what they say. If
you do need a EDFA, they are not that expensive but the site is
expensive and requires power (+ backup). See if it’s possible to
put the EDFA in the end facilities to get enough power for the
Testing PCS Fiber
We Get Many Questions From Our Instructors Also
Q: I recently did a CFOT
training class for a government agency. They use 200
micron core fiber in short sections (50 ft. the longest) within
aircraft. The connectors are SMA 905s. The cable specs
state that there is 8dB of loss in 1 km at 850nm. I have
searched but cannot find any info regarding how to test the
cable/connector links. The OLTS they have uses 62.5/125
jumpers. Is testing these cables with the above OLTS setup at
850 nm a valid testing method?
A: That’s 200/240 PCS or HCS fiber - plastic clad silica or hard
clad silica step-index fiber - that has a glass core and plastic
cladding. It has been used on a lot of platforms because it’s
large core makes connection alignment easy. The SMAs are used
because the connectors are air gap connections so vibration will
not cause scuffing that you can get with PC - physical contact
connectors. On aircraft, the 1/4-36 nuts on the SMAs are usually
Testing can be done just like any other cable plant with a
double-ended test (OFSTP-14) for the whole cable or a
single-ended test (FOTP-171) to check the connection on either
end. You need a 850nm LED source and a meter with a large
detector (>2mm) to pick up all the light and an adapter for
SMA connectors. You also need launch and receive cables of
matching fiber and connectors about 2m long. No worries about
mode conditioning since the step-index fiber is a mode mixer
Fiber attenuation coefficient of 8 dB/km sounds about right.
Connection losses ~0.5-1.0 dB are normal. A typical patchcord
would have a loss of ~1-2 dB.
To get a microscope to view it might be difficult.
Q: I have
10 kilometers of singlemode cable installed that was not
labeled. It has been suggested that we shoot a VFL down the
fiber and label it. I am having trouble finding a VFL that will
shoot this far. Any ideas?
A: Occasionally we see some imported VFL that claims to go 10km
or more. That tells us the company is clueless about fiber
optics. VFLs work at ~650nm in the visible red spectrum while SM
is optimized for 1300-1600nm in the infrared where it has a loss
of ~0.3dB/km. At 10km it has a total loss of ~3dB or half the
input signal. At 650nm, singlemode fiber has a loss of ~10dB/km
which means it loses 90% of its power per km. At 10km, you have
100dB of loss - leaving you with 0.00000001% of the input power
- not much!
VFLs have enough power for 2-3km max. To identify fibers at
10km, you need a 1310nm laser source and a power meter to do
continuity. Or a gadget called a fiber identifier. For more
WiFi Access Points In a Passive Optical LAN
Q: If we
install GPON passive fiber optical LAN in a new hotel, would one
need to run fiber to every AP? Since every hotel room needs an
AP this gets expensive. Any suggestion on the simplest and less
expensive way of connecting Fiber Cable to an AP in the
A: You do not need a fiber to every wireless AP in a GPON
passive optical LAN (POL). The AP needs a UTP (Cat 5e/6) cable
with Gigabit Ethernet and POE (Power over Ethernet)
capability. The POL fiber should terminate in a multiport
switch that has a fiber input and then 4 or more UTP/POE outputs
for the wirelses APs. That’s the cost saving architecture of a
GPON POL. See this page in the FOA Guide:
You should also check out the APOLAN website (http://www.apolanglobal.org)
for more information on hospitality applications with POLs.
Q: I am
wondering how the landscape will change as the nation moves from
4G-LTE to 5G. Will it use the same network as currently, or will
the network need to be updated or replaced? To what extent will
5G be dependent on wireless vs fibre optic? Will the
infrastructure nationally move more toward an underground wired
one, rather than a Radio Access Network?
A: The wireless network is totally dependent on fiber optics for
it’s communications backbone. The “wireless” part is the
connection from an antenna to the mobile device. From that
point, the network is cabled, mostly fiber already and soon to
be all fiber.
4G/LTE and soon 5G in urban areas is moving to “small cells”
with about 10X as many cell sites covering much smaller areas.
Every small cell site needs a couple of fibers. Metro backbones
will require very much larger fiber counts, especially with
C-RAN (centralized radio access network) architectures now being
An example is Santa Monic, CA where we live. It has about 200K
citizens, 8.9 square miles(about 23 sq km), but has planned for
600 small cell sites, spread over multiple service providers.
At FOA we see wireless as one of the most active areas for
fiber, along with data centers.See http://www.thefoa.org/tech/ref/appln/wireless.html
Q: What are
good OTDR settings for a 300-500m fibers? We’re using a 1.5 m
launch cable and sometimes got (-) loss,
A 1.5m cable is not a launch cable. A launch cable must be long
enough to allow the OTDR to settle down after the test pulse.
THe negative loss is because the OTDR has not settled down
Generally the minimum launch cable for testing short cables
would be 10-20m for MM, 100m for SM. Then use the shortest test
pulse, ~1km range, average enough to reduce the noise.
Q: I was told a contractor installed arsenic
coated fiber optic cable because they didn’t want animals to
chew through it. Is this true?
A: Some cable has
chemicals put in the jacket to make it taste bad to rodents. We
have not found any one who claims to use arsenic, in fact, we
could find no references to what kinds of chemicals are used.
Do Cables "Go Bad"?
Q: It’s been my observation over ~15 years of building
and managing fiber channel storage area networks that from time
to time cables will fall out of transmission spec. In
terms of communicating with non-storage people, they in essence,
“go bad”. Other than possible damage due to physical
disruption of a cable, or contamination at the connectors
usually caused by a human being unplugging/replacing, has it
been your observation that MM cables can “go bad”?
A: There are some
possible causes of problems over time. We know of connectors
that fail for several reasons.
say fiber requires no maintenance - set it up right and lock it
up. As you pointed out human intervention is often the issue.
biggest cause is with prepolished/splice connectors with
mechanical splices. the assumed problem is the index
matching get goes bad, but that’s highly unlikely. It’s
usually the crimp fails and the fiber pulls out, especially
if it has any stress on the fiber.
connectors can have a bond between the connector and fiber
fail, more likely on anaerobic connectors.
stress on the fiber at the connector is bad. Patchcords
should not be left hanging on racks but dressed into
horizontal racks below each patch panel.
stress in cables can be a problem - tension or tight bends -
and they may get worse over time.
is always a worry. It takes years to show up, but indoor
cables are not protected from moisture like OSP cables.
course, transceivers fail too - electronics are generally
very reliable but do deteriorate over time and cause
Ports Or Media Converters?
Q: Should I Buy A Switch With Fiber Ports Or Use Media
A: I’m assuming you are
thinking of using a switch with copper Ethernet ports and a
media converter instead of a switch with fiber ports. The
downside is that it adds complexity and increases the chance of
failure. My analogy is something my primary flight instructor
told me many years ago - multiengine planes are not safer
because having two engines doubles your chance of having an
engine failure. IBM still says that most network problems are
cabling problems. Using media converters adds more electronics,
more power supples and more cabling connections.
PON Meters And Sources
Q: We're evaluating PON power meters and test sources.
How should we test them? Do we need a PON network?
A: There is no
requirement for having a PON to test the meters. I would check
it against a meter you trust to test
1) if the reading of absolute power (dBm) agrees - should be
within +/-0.2dBm. Compare at several power levels, as high as
possible (~0dBm with a laser), medium, (~ -20dBm) and very low
2) make some loss tests of cables and attenuators over the range
of 1-5-10-15-20dB and compare to a meter you trust.
3)the extra calibration at 1490 is not an issue - the difference
between 1490 and 1550 is very small and providing that
calibration can be more a confusion factor since there are no
transfer standards for that wavelength.
3) The big issue with sources is stability. Connect the source
with a short cable to a trusted power meter, connect it to its
power supply, turn it on and monitor the output over time. There
should be a short warm-up period and then it should be stable
within a few 0.01s dB. Let it run on batteries until the
batteries run down to ensure that the source has a proper power
supply that keeps the light output stable over time as the
Loss At 1383nm?
Q: We tested one link of 90.8 km at 1310/1383/1550nm
and we got high loss at 1383 while other wave lengths have good
results. What's up?
A: That wavelength is
the center wavelength of the OH+ water peak, so you are seeing
the extra attenuation there. Older fibers will have attenuation
of 2-3 dB/km at that wavelength but new “low water peak” fibers
will be <1dB/km. See “Low Water Peak Fibers” here http://www.thefoa.org/tech/ref/OSP/fiber.html
Q: Are there different grades (micron) polishing
films/papers for multimode and single mode fiber cables in ODF
termination ? If yes, What are the grades polishing papers for
multimode 50/125 um and 62.5/125 um fibers.
A: The polishing of MM
and SM fiber is indeed different. Both start with an “air
polish” with 12micron alumina polishing film to remove the
protruding fiber. Then the polishing continues on a soft
polishing pad (3mm 80 durometer rubber).
MM uses a 3micron alumina polishing film polished dry then a
final 0.3micron alumina film polish. See
SM is usually done with a wet polish using as special polishing
slurry and diamond polishing film. The diamond film will polish
both the ferrule and the fiber to get the best end finish. See http://www.thefoa.org/tech/ref/termination/sm.html
There are even more pages of information on the FOA Guide at http://www.thefoa.org/tech/ref/contents.html#Components
Q: Can I get an indoor armored 8 core fiber optic
A: Most cable
manufacturers make indoor armored cable using corrugated wrap
armor to protect cables from crushing loads from other cables
especially in under floor installations.
Q: Is there a current standard, for maximum allowable
loss, for MPO fiber connectors? If so… what is the standard #
from EIA/TIA? (Was it amended in 568B, since they were
introduced?) Would it be similar to standard connectors @ 0.75dB
Max allowable loss?
A: The MPO is covered
under the TIA 568 standard. All fiber optic connectors are the
same - 0.75dB.
There are discussions being held at TIA and ISO/IEC on using a
different method of specification, statistical in nature, that
says X% would be less than YdB in several stages from 0.1-0.2 to
over 1dB, but it’s led to some headed discussions.
MPOs for MM are probably no less than 0.5dB and SM are near the
0.75dB mark. At least the SM ones are APC (usual 8 degrees, but
still a flat polish).
I’ve recently learned that MPOs are polished for fiber
protrusion to try to get fiber contact, but the evenness along
the line of fibers is harder to control.
image from SUMIX
showing protruding fibers in MPO connector
More Than “Single” Mode?
Q: We're now using SM fibre so it looks like we don't
need mandrels in the Ref Lead at the Light Source. The
info I have is that we need to make a couple of air coils 35mm
to 50mm in diameter. Why?
A: When you launch from
a pigtial laser source through a connector into a reference
cable, you do have several modes being propogated. It usually
takes 100m or so for the second or third order modes to
attenuate. So the coil causes them to be attenuated by the
stress enough to no longer be significant - it’s a mode filter
just like MM. If you do not do this, you will measure higher
loss in the fiber and at connections near the source. Since most
SM has traditionally been long distance, the effect was small or
ignorable, but with short links, it can be significant.
Followup Q: But how do we explain multiple modes in Single Mode
A: When you get the core of the fiber down to ~5-6 times the
wavelength of the light, it no longer acts like geometric optics
(like MM fiber). Some of the light can travel outside the core
(see the note on “waveguide
At launch, significant amounts of power are at higher angles
creating short lived modes that are highly attenuated.
Replacing OM1 MM Fiber
Q: We are an automation system integrator in South
Africa. We have a client that has multimode 62.5/125 fibre optic
plant wide. None of the runs between components are longer than
2km. We intend to upgrade the technology from a proprietary
communication protocol to a standard ethernet protocol at 100
MHZ. The fibre to copper convertors we will be using are using
1300nm light source and have a Fibre Optic Link Budget of 12.8dB
for 62.5/125 um and 9.8dB for 50/125 um. The
client has been advised to replace the multimode 62.5/125 with
multimode 50/125 cabling and we need to know if this is really a
A: Do you know how old
the fiber is? It should be what we called FDDI grade 62.5/125
fiber with a loss of ~1dB/km and a bandwidth of 500MHz-km
at 1300nm. A 2km link should have a loss of 2dB for the fiber
and ~0.5dB/connection - well under the power budget of the link.
100Mb/s Ethernet variants were designed for 2km or more on this
fiber. There is no reason to upgrade at this time, 50/125 fiber
would not be needed until Gigabit Ethernet was desired.
Bi-Directional OTDR Testing
Q: Should the testing be done with the same piece
of equipment from both ends then merge the results or does that
not matter - can you use traces from two OTDRs as long as the
test equipment is compatible and settings are adjusted properly.
A: Yes, you should use
the same test set from each end but this way - take a trace,
disconnect the OTDR from the launch cable and go to the far end
of the receive cable and connect it there to take the second
trace. The usual way people do bi-directional tests is to
disconnect the launch cable and take it to the far end and shoot
back up, often not using a receive cable at all, figuring they
get the far end connector on the second test. But when you
disconnect the launch cable (and/or the receive cable) you lose
the connection you want to test in the other direction! As for
using the same OTDR, every OTDR is different and the results you
get may be significantly different, esp. if they are not
calibrated recently - and few OTDRs are ever calibrated.
OLANs in Hotels And Resorts
Q: Are passive OLANs a good choice for hotels or
A: Passive Optical LANs
are enterprise networks based on fiber to the home (FTTH)
technology not Ethernet over structured cabling. The FTTH
network is usually using GPON standard equipment over one
singlemode fiber with passive optical splitters that provides
basic Level 1 and 2 network functionality. This is not Ethernet
but carries Ethernet over the GPON protocols at 2.5G downstream
and 1.25G upstream.
Passive OLANs offer several advantages over conventional
Ethernet switches and structured cabling, including much less
cost (~50% capital expense and ~20% operating expense),
much lower space requirements (see the link to the library
photos below and note the two racks of equipment that support
4000 drops), longer distance requirements (to 20km), easy
expansion (these are systems designed for hundreds of thousands
of users) and easy management (when you have hundreds of
thousands of users, that’s important.)
For hotels, convention centers and similar facilities, the ease
of upgrading to a passive OLAN is a big advantage - one fiber
goes from the computer room to a splitter where it can serve 32
switches of 4 ports each. That’s right, one fiber can support
128 users! It can support anything that a network can - wireless
access points, security cameras, secure entry systems, VoIP
phones or POTS phones - anything that will run over a
Q: I have a question about the OLTS - do you have to
recalibrate it every day ?
A: Any optical loss
test set needs to be calibrated for “0dB” whenever anything
changes - the launch cable - source output - or even every few
tests to ensure the connector is clean and undamaged - plus they
wear out. See 5
different Ways To Test Fiber Optic Cables.
Q: I have not been able to find a good definition of
“optical insertion loss” or “insertion loss” or “optical loss.”
A: Insertion loss was
the term originally used for the loss of a connector tested by a
manufacturer. They would set up a source and length of fiber
connected to a meter, measure power, insert a pair of connectors
and measure the loss. Since it was an inserted connection, it
became known as insertion loss.
Over time, the term insertion loss became more widely used to
contrast with the loss measured by the OTDR, an indirect
measurement using backscatter that may not agree with the loss
with a light source and power meter.
Insertion loss, therefore migrated to meaning a loss measured of
a cable or cable plant inserted between the launch and receive
cables attached to a light source and power meter for double
ended testing used with installed cable plants. For patch cord
testing, you do not use a receive cable attached to the power
meter but connect it directly to the cable under test, making
the test just include the one connection to the launch cable.
Two other terms often mixed up are attenuation and loss, which
are essentially the same, except when discussing a fiber. In
fibers, attenuation is often used instead of attenuation
coefficient. Attenuation is the absolute loss i dB while
attenuation coefficient is the characteristic attenuation of a
fiber expressed in dB/km.
Here is probably the best explanations: http://www.thefoa.org/tech/ref/basic/test.html
Q: We are looking at a company’s fiber network which
has been laid at various points in time over numerous
years. In this process, we are trying to identify the
changes that were made to either/both the glass fiber and the
cladding. Are there different generations of what was
industry standard in creating the fiber? For example, are
you able to identify the difference in a fiber that was laid in
1980 versus one laid today? Was the cladding the same
size/thickness etc. in 1980 as it is today or has this been
modified/improved upon over the years? In all, we are
trying to find what modifications have been over the years and
how this may improve the life of the network and its
A: This is a common
problem today. Many network operators are evaluating their fiber
networks for upgrades, hampered by the fact that few are
properly documented. Below is a timeline that should answer your
questions. What many network owners are doing now is testing
their cable plants - a process called Fiber
Characterization. There are contractors who do this
First field trials, US and UK, using multimode fiber at 850nm
First long distance networks still using multimode fiber at
850nm, planning to upgrade with wavelength-division
multiplexing at 1310nm
singlemode fiber becomes feasible, telecom drops multimode
fiber, all future installations are singlemode - this first SM
fiber with a 9 micron core and 125 micron cladding is still
available today but with better specifications. Really early
fiber may not have good environmental protection and degrades
over time. Early speeds were 145-405Mb/s, up to 810Mb/s by the
end of the decade.
around this time, modern fiber begins - better performance and
environmental protection. Fibers for wavelength-division
multiplexing in the 1500nm range appear allowing multiple
signals on a single fiber and fiber amplifiers allow long
- massive build-out of fiber backbone leads to glut of fiber -
WSJ ~2001 says 93% of all fiber is dark. Speeds grew from
1.2-10Gb/s over the 90s decade
- massive Internet growth and mobile device growth eats up
glut of fiber and demands many times more. Dense
wavelength-division multiplexing becomes the norm. Speeds
began at 1.2/2.5Gb/s, upped to 10, 40 and are now at 100Gb/s.
So most fiber installed after 1990 has the possibility of being
used at 10Gb/s, after 2000, it’s probably OK for 40Gb, and since
2010, you are probably OK for 100G and maybe more. To
verify performance, you test each fiber for connector condition,
loss, spectral attenuation, chromatic dispersion and
polarization mode dispersion. There are test sets that will do Fiber
Characterization in basically one step.
Fusion Splicing Live Fibers
Q: Is it safe to fusion splice a live fiber, or is
there a chance that
the light from the arc will damage the detectors in the modules
at the end (20km-rated SM for us).
A: I have never heard of
this being a problem. The amount of light coupled into the fiber
from the splicing would be very small compared to a properly
coupled laser. When a cable is broken you might be splicing the
fibers that are live without knowing which are live and not
caring. On your newer splicers this is not a problem. On the
older splicers with the LID system you would have to reduce the
power to get a good splice which they would do by putting a bend
in the Fiber.
Communications Over One Fiber
Q: Is true duplex over a single fiber possible, or is
more like a shared time-domain technique in a quasi-duplex mode?
I would guess that true duplex would lead to interference
A. Bidirectional links
are widely used - that’s how FTTH PONs work. They use splitters
to combine/split the signals and one wavelength downstream and
another upstream. See Fiber
Optic Datalinks and for FTTH FTTH
Hybrid 2.5-1.25mm Connector Mating Adapters
Q. Can I use the hybrid 2.5-1.25mm adapters for
connecting SC connectors to LCs or MU connectors. It would make
testing much more convenient.
A: We do not recommend
them for most uses, especially testing, as they can be highly
unreliable. Reserve them for emergencies and use hybrid patch
Test MM Fiber @ 1300nm?
What is your opinion about the need for testing at 1300
nm on OM3 and OM4 fiber especially now that bend insensitive
multimode fiber is taking over?
unnecessary and costly. It’s rooted in the FDDI/100M days 25
years ago when 1300 LEDs were used and is now obsolete. The
only actual uses at 1300nm I know are the extremely rare
systems using 1310 lasers which may be standards but simply
don’t seem to ever be used. As you say, BI fiber makes the
issue of finding stresses moot.
Fiber In Service Loops
Q: We designing a rural utility system that will be
expanded to FTTH (or FTTR - fiber to the ranch in this case).
We're wondering how much excess fiber in service loops to add.
One software package is asking for 12% but that seems excess.
have typically seen 100 feet on straight through boxes
(reserves), 35-50 feet on cut ends for splicing and anywhere
from 15-25 feet at the premise depending on how much is
required for the termination device, positioning, etc. When
rough estimating we have typically used 10% over linear
Maintenance of Fiber Networks
Q: Can you guide me how to prepare Optical Fiber
Cable Annual Maintenance Proposal?
A: Basically, the
network needs to be installed properly, fully tested and
everything carefully documented. Then no routine maintenance
is required. Most problems with fiber optic networks occurs
when techs are working with it, e.g. damaging cables or
getting connectors dirty when testing, so leaving it alone is
the best plan.
Electronic transmission equipment can be tested anytime to
ensure proper data transmission, but that does not involve
accessing the fiber.
We have several things which may be of help:
You Tube Video: FOA
Lecture 39 Maintaining Fiber Optic Networks
Web page: Maintenance
I have 4 questions about OTDRs:
Q: What is dynamic range I read many time but
can’t understand yet, whether it is a range of losses can be
measured by OTDR for example if an OTDR has 45 dB dynamic range,
it can read the losses of point up to 45 dB or what it means.
A: I do not believe there is a standard definition of
dynamic range, but it is generally accepted to be the highest
loss of the longest cable where you can see the end of the
cable. That usually means using the longest test pulse and most
averaging and assuming the end of the cable has a
Q: What is dead zone is it fixed in meters mean an
OTDR cannot measure up to initial 5, 10 or 20 meter
A: The dead zone is a function of the pulse width and
speed of the OTDR amplifier. For most OTDRs it’s about 2-3 times
the test pulse width.
Q: What Type of settings needed before launching a
A: See FOA
Lecture 18: OTDR Setup or the section "Modifying OTDR
Setup Parameters For Best Test Results” in
testing. A: Basically you set up wavelength(s), test pulse
width (long enough to reach end of cable but short enough for
best resolution), index of refraction or group velocity (a
function of the fiber type and wavelength) and the number of
averages (enough to mitigate noise but not take too long)
Q: Reading a test with 1310nm and 1550nm - why values
different for a same length of fiber.
A: The attenuation of the fiber will be different at
each wavelength and the index of refraction which is different
at each wavelength causes a difference in length. The OTDR
measures length by measuring time and then multiplying that by
the speed of light in the fiber (which is the inverse of the
index of refraction.)
The FOA page "Frequently
Asked Questions About OTDRs" answers these
questions and more.
Old Cables Out Of Conduit
Q: How do you get old cables out of a conduit when
they are stuck?
A: Usually we are concerned about reducing friction
when pulling cables through conduit, but sometimes you need to
get them out. Here
is a page from American Polywater the leading lubricant
company with advice on the subject.
Q: Is there a guide published by FOA that provides
insight as to the process of fiber optic manufacturing? It's my
understanding that the guide stresses quality and controls to
ensure performance and reduce product loss?
A: We do have a guide
for manufacturers. It is mostly aimed at communications systems
and components manufacture. Here
is a link to download it.
Long Does Termination Take?
FOA received a request from a consultant recently wondering if
we had information on the termination times for fiber optic
cables. After some looking in our archives, we realized we had a
document online that compared times for various fiber optic
termination processes. The paper was written after several FOA
instructors did a comprehensive time and motion study on
termination processes. The document is about 15 years old but
can read it here in the FOA Online Guide.
Connectors (From A Patchcord Maker)
Q: What are the chief defining standard(s) that
specifies connector and assembly IL (insertion loss) and RL
(return loss or reflectance) for both SM and MM fiber?
A: The description on
our Guide is here: http://www.thefoa.org/tech/ref/testing/test/conntest.html
FOTP-34 covers connector testing as a qualification test
for the type of connector - basically a "destructive" test for
Reflectance is described on that page and here also: http://www.thefoa.org/tech/ref/testing/test/reflectance.html
Testing an assembly like a patchcord is covered under
Tests For Fiber Optic Cable Plants
Q: I did some research and I noticed that there is a
bunch of tests that can be done to fiber optics and I was
wondering if there is a list of primary tests that can be done
as a basic test.
A: Fiber optic testing
does have a hierarchy of tests.
Here is a
link to a page on the FOA Guide site that explains the
the top of the list is "insertion loss" testing which uses a
light source and power meter to test the fibers in the
same way that a communications system transmits over the
fiber. It is a simple test and the equipment needed is
will also use a microscope to inspect the fiber optic
connectors for dirt and damage, a big issue for fiber.
instrument called an "OTDR" takes a snapshot of the fiber
using a technique like radar. Most outside plant cables are
tested with an OTDR and the data ( the snapshots are called
"traces") stored for future reference. OTDRs are more
expensive and require more training to use properly.
FOA also has information just for users of fiber optic networks,
to Clean POF (plastic optical fiber)
heard that plastic fibres such as PMMA can suffer damage from
cleaning from an alcohol solution. Are there alternate cleaning
solutions available for these types of fibres."
A: You can use a 10/90
mix of isopropyl alcohol/water. Typically use with a lint
free swab. (from out POF consultants)
Bare Fibers With OTDR
Q: We are starting to test some OPGW cables. We have an
OTDR but we don’t find some reusable connectors. If we have to
test an OPGW with 48 fibres, we can’t set up 48 SC connectors!
Are there some reusable connectors in the commerce?
A: I assume you mean you
need to test with a bare fiber on the OPGW. For testing bare
fiber, use a splice, not a connector. Have a long pigtail on the
OTDR as a launch cable, long enough for the test pulse to
settle, say 100-500m, then use a splice for a temporary
connection. You can fusion splice the fibers then cut the splice
out or use a removable splice like the Corning Camsplice
If you use a mechanical splice, you need a high quality cleaver
just like with fusion splicing and after several uses, you need
to add more index matching gel or liquid - mineral oil works OK.
the FOA page on Testing
Is A Flashlight Test Adequate?
I contracted a firm to install an OM3 of 200 meters. On
one end I have an SFP 1000SX ,on the other a 1000SX
converter from optical to UTP. We made pings but they never
reached, and I didn’t see the laser at the extreme of the fiber.
They promised me to send me the certification they supposely
made ,though they assured me the fiber is ok, because WITH
A FLASHLIGHT THEY SENT WHITE LIGHT FROM ONE SIDE TO THE OTHER
AND IT WAS VISIBLE. I saw the light too, and I thought the
culprit was my switch or my SFP. I want to know: is this a good
demonstration that the fiber is ok?
A: A visual continuity
test is not adequate - your eye is not calibrated! The power of
the lamp is unimportant as each eye’s sensitivity is different.
And your eye probably cannot see the light from a 850nm VCSEL
source - most people’s eyes are not sensitive at that infrared
wavelength. The installer should have tested the link with a
light source and power meter (http://www.thefoa.org/tech/ref/testing/test/OFSTP-14.html)
and given you the loss in dB. The connectors should also be
inspected with a microscope to ensure proper polishing and
(http://www.thefoa.org/tech/ref/testing/test/scope.html). If the
SFP output is -6dBm, what is the power at the receiver?
1000base-SX is supposed to work with 4.5dB loss (see
http://www.thefoa.org/tech/Linkspec.htm). The fiber loss should
be ~0.6 dB, so you must have >4dB connector losses! That says
bad installation! The 1000SX link should work over 200m if the
fiber has been properly installed.
Q: I have some 62.5 mm and sm inside fiber plant over
20 years old. When is a good time to upgrade?
A: When you need to or
have to. If it's working OK, there is no need to upgrade!
"Connector Loss" or "Connection
Q: I have always counted the loss of a connector as .75
dB (568B-3) and 1.5 for a mated pair. Is that correct?
A: While the industry
always says "connector" loss, it is actually "connection" loss.
As we explain in the page on termination and splicing (http://www.thefoa.org/tech/ref/basic/term.html)
When we say "connector" loss, we really mean "connection" loss -
the loss of a mated pair of connectors, expressed in "dB." Thus,
testing connectors requires mating them to reference connectors
which must be high quality connectors themselves to not
adversely affect the measured loss when mated to an unknown
connector. This is an important point often not fully
explained. In order to measure the loss of the connectors
you must mate them to a similar, known good, connector. When a
connector being tested is mated to several different connectors,
it may have different losses, because those losses are dependent
on the reference connector it is mated to."
TIA spec of 0.75dB is for a mated pair of connectors. If you
have been passing connectors tested @ 1.5dB loss....you may have
some very bad connectors in your cabling!
Q: I am doing a lot of fiber optic jumpers for control
systems, either single mode or multimode. I want to get a
scope to inspect the ends after I clean them would you recommend
a 200X, 400X handheld or one similar to a Noyes OFS 300
A: We prefer to use
lower magnification and have a wider view so I can see more of
the ferrule to determine its condition. You can see the fiber
effectively at 100X but 200X may be better. 400X may be too much
for most tasks like inspecting for cleanliness, but may be good
if you are polishing SM for good reflectance. We've used the
Westover units for years because they offer two different
methods of illumination - direct and at an angle. If you are
doing a lot of patchcords, I recommend a video microscope. I've
used the Noyes unit that interfaces to a PC to create the FOA
Microscope Inspection YouTube video here: http://www.youtube.com/watch?v=IyumH8CiUPQ&feature=youtu.be
and it works well.
Q: Who can I contact regarding recycling cable I am
removing from a building?
A: Here are some people
who say they recycle fiber optic cable or at least know how to
Hint: Did You Know You Have A Fiber Optic Tester In Your
That old mobile phone has a camera which may be sensitive to
infrared light - lots more than your eye - and can detect
light in an optical fiber or from a transmitter. Chris
Hillyer,CFOT/CFOS/I, Master Instructor, Northern California
Sound & Communication JATC sent us some photos showing how
this works. See below
or the video
now on YouTube. Update: You should check out your old
cell phones before you recycle them. We've found older models
use sensors which are better at infrared than the newer ones
which take better pictures. This is a good use for your old
cell phones hiding in the drawer!
This is a topic we keep reminding everybody about, and here is
a contrator in the Middle East: Here some samples of the
connectors for SM fiber already installed in the system we were
you can see, the dirt is large compared to the size of the fiber
(dark gray), and the core (not visible here) is only 9/125 of
the overall diameter of the fiber!
Every Connector - A Lesson We Learned From Creating Lessons
curriculum, we got inputs from many experienced techs about the
testing requirements. Everyone we talked to made a big point
about cleaning and inspecting connectors before testing. Dirty
connectors are a major problem with errors in testing. We've
also seen that many installers think that if a connector,
especially new connectors, has a "dust cap" on the connector, it
does not need cleaning. WRONG!
The common name for the plastic caps on connector ferrules is
"dust cap" and a friend says they
are called "dust caps" because they are full of dust.
Those plastic caps are made by the millions, popped out of
plastic molding machines into barrels and stored until put into
plastic bags. Whenever you remove one of them, clean the
connector before testing or connecting it.
More on connector cleaning is here and here.
on cleaning. See Product
News below for links to vendors of fiber cleaning products.
You Need To Know About Fiber Optic Cleaning And More
Forrest, one of the industry experts on cleaning fiber optic
connectors, retired about a year ago. We encouraged him to put
down on paper what he knew about fiber cleaning and he took our
advice. He's now created 4 books on cleaning topics that cover
just about everything you need to know. And he added another
volume that's also important - maintaining fusion splicers. We
recommend these books highly.
How to Precision Clean All
Fiber Optic Connections
Understanding Cross-Contamination Points on Fiber Optic
Inspection & Test Equipment
Maintaining a Fiber Optic Fusion Splicer
Comparison Study of Precision Cleaning Methods for All Fiber
Whitepaper: The Significance to Optical Internconnect:
Properly Cleaning a Fiber Optic Connection
Information on Ed's books is at http://fiberopticprecisioncleaning.com/available-books-whitepapers/.
news about Fiber Optic Cleaning Videos on YouTube by ITW
Fiber Optic Cleaning Videos on YouTube
See news about Fiber Optic Cleaning Videos on YouTube by ITW
Chemtronics three fiber optic cleaning videos on YouTUbe
Cleaning. They are good explanations of cleaning processes
- the Wet-Dry is especially interesting.
Uncertainty: Everyone testing fiber optics should understand
that every measurement has some uncertainty - whether you are
measuring loss, length, wavelength, power, etc. Knowing that
uncertainty is very important to interpreting the measurement.
It's worthwhile to read and understand the issue of measurement
accuracy covered in this
page of the FOA Online Fiber Optic Reference Guide.
Reading or Watching:
up at the FOA Pinterest
continuing quest to help people understand how to test fiber
optic cable plants and communications systems, we've created two
more "QuickStart Guides to Fiber Optic Testing." They are
simple, step-by-step guides on how to test fiber optic cable
plants, patchcords or single cables using insertion loss or OTDR
techniques and optical power from transceivers. It's as
straightforward as it can get - what equipment do you need, what
are the procedures for testing, options in implementing the
test, measurement errors and documenting the results.
It can't get much simpler.
Send anybody you know who needs to know about fiber optic
testing here to learn how it's done in a few minutes.
Fiber Optic Cable Plants And Patchcords
Fiber Optic Cable Plants With An OTDR
Optical Power In Communications Systems
Crossword Puzzles? Here's Some On Fiber Optics
Do you like
crossword puzzles? How about one on fiber optics - or maybe a
half-dozen of them? FOA Master Instructor Eric Pearson of Pearson
Technologies has created a series of crossword puzzles on
fiber optics that are keyed to the FOA CFOT reference materials
and his book Professional
Fiber Optic Installation, v.9. You can have fun and
study fiber optics at the same time!
This months crossword puzzle is on "Optoelectronics and
Splicing" - Download
the crossword puzzle on "Optoelectronics
missed the earlier puzzles, here they are:
the PDF file of the crossword on "Light and Fiber".
the PDF file of the crossword puzzle on "Cables".
the crossword on "Connectors
Fiber, Do You Know How Good It Is?
millions of miles of long distance fiber installed around the
world and most of it likely to see an upgrade of the systems
operating on it, probably in the near future. Twenty years ago,
most of it was probably running at ~1Gb/s, ten years ago it was
probably 2.5 Gb/s, recently it was likely to be 10Gb/s but now
many are being considered for 100Gb/s or beyond. Can the fiber
support such speeds? Can it be "repaired" or "modified" to make
it possible to use it at higher speeds? If you own that fiber,
can you say what it is worth without knowing its future upgrade
In order to know the potential for upgrades on your cable plant,
you need to test it. This process involves a number of tests and
is called "fiber characterization." Greg Stearns of TTP-US, an
FOA Corporate Member, performs these tests and has written a
short article on why you need to characterize fiber and how its
done. Read about fiber characterization from someone who does it
often and can explain it well.
the paper here (PDF, 80kB).
Singlemode Fiber Types
fiber has a lot of names and users are confused by the different
names depending on the standards organization you refer to IEC,
ITU or TIA designation. Most widely used are the ITU G65X
designations but even there we find many designations. Shaun
Trezise of M2FX has posted a simple explanation on the company
blog that helps explain the different types and where they are
more on the M2FX blog
There is a cross
reference to the IEC, ITU and TIA designations on the FOA
Offers Super Posters And More
EXFO offers some super posters, guides and books. The FTTx and
OTDR posters are really useful! Look
at the whole selection here.
Getting Cables Out Of Conduit
Usually we are concerned about reducing friction when pulling
cables through conduit, but sometimes you need to get them out.
is a page from American Polywater the leading lubricant
company with advice on the subject.
What Is The FOA?
Hear FOA President Jim Hayes tell the FOA Story in a 2-part
interview by Sound & Video Contractor Contributing Editor
Bennett Liles. It tells about the FOA history, goals and
Part 1: http://svconline.com/podcasts/audio/fiber_optic_association_part1/index.html.
Part 2 http://svconline.com/podcasts/audio/inside-fiber-optic-association2-0924/index.html.
Happens To Old Fibers?
In a recent web search, we found this article from Corning,
reprinted from a IWCS presentation in 1995. It discusses
extensive tests on a 1984 cable installed in the northern US to
see how it had degraded in almost 10 years. It is interesting to
see how the fiber survived OSP exposure. Read
Standard Is Comprehensive Guide To Customer Cabling (Get your
answering a recent technical questino, Trevor Conquest in
Australia pointed to the Australian Standard "Installation
Requirements For Customer Cabling." When we checked, it is on
the web and can be downloaded. It's a big book - 220 pages -
full of details for fiber and copper installations. We recommend
yourself a copy - go here.
fiber inspection probe technical specifications -
intent of this application note is to promote a better
understanding of video inspection probe specifications and
features. Properly understanding the key specifications
and features will greatly facilitate the decision process
involved in acquiring such devices. Understanding the key
aspects of fiber inspection probes will also help users
understand how fiber inspection probes operate, thus
enabling them to maximize the full potential of these
In The US Do Contractors Need Licenses For Fiber Optics?
get asked where in the US do contractors doing fiber optic
installations need licenses. We found a good website for that
information, the NECA -NEIS website. You might remember
NECA-EIS, as they are the partner with the FOA in the NECA/FOA
301 Fiber Optic Installation Standard. NECA is the National
Electrical Contractors Association and NEIS stands for National
Electrical Installation Standards. They have a very easy to use
map and table that gives you data on every state in the US, so
mark these pages for future reference.
(See “State Regulations”)
(all electrical licensing)
Low Voltage: http://www.neca-neis.org/state/index.cfm?fa=specialty_licensing
OFS invites you on a tour of their multimode fiber manufacturing
facilities in this new 5-minute video. You will see their highly
automated manufacturing operation in Sturbridge, Mass.,
including their patented MCVD preform fabrication process to
fiber draw and final product testing. With a technological
heritage dating back to AT&T and Bell Labs, OFS has been
manufacturing high-quality multimode fiber since 1981.
the video here.
Fusion Splicing And Selecting Singlemode Fiber
We've been asked many times "How long does it take to splice a
cable?" It's not a simple answer as it varies with the number of
fibers in the cable and the work setup, including whether one or
two techs are working at a job site. FOA Master Instructor Joe
Botha of Triple Play in South Africa did his own analysis based
on decades of experience both splicing cables and teaching
others how to do it properly. This is one of the best analyses
we have seen because Joe includes prep times as well as splicing
times and differentiates between one tech and two techs working
together. He adds some other tips on fusion splicing too. This
should be mandatory reading for every tech and given to every
is Joe's splicing analysis.
Joe also has an excellent writeup on how
to choose singlemode fiber that helps understanding
the different types of G.6xx fiber. Read
And you will want to read Joe's report on splicing
different types of SM fiber, including bend-insensitive
(G.657) fiber. Read
- Mike Holt's Explanation Of The US National Electrical Code
(NEC) For Communications Cables
is the acknowledged expert of the US National Electrical Code
(NEC). His books and seminars are highly praised for their
ability to make a very complicated standard (that is in fact
Code - law - in most areas of the US) easily understood. Part of
the appeal is Mike's great drawings that make understanding so
much easier. Mike makes Chapter 8 of his book available free. It
covers communications cables, telephones, LANs, CATV and CCTV,
for premises applications. Even if you live in a region or
country where the NEC is not the law, you may find this
Mike's Chapter Here.
Optic Cleaning Videos on YouTube
Chemtronics has three fiber optic cleaning videos on
Cleaning. They are good explanations of cleaning processes
- the Wet-Dry is especially interesting.
yourself a copy and read it!
Technical Website For Installers
has one of the best technical website for cable installers. Check
out their website, especially “Videos,” “Engineer’s Corner”
and “Calculators.” http://www.polywater.com/NNNBSL.pdf
Optic Safety Poster
We've had numerous requests to reprint our guidelines
on safety when working with fiber optics, so we have
created a "Safety Poster" for you to print and post in your
classroom, worksite, etc. We suggest giving a copy to every
student and installer.
Tech Topics -
Fiber Optic Tester In Your Pocket? (See the video on
The camera in your old cell phone is sensitive to infrared light
- lots more than your eye - and can detect light in an optical
fiber or from a transmitter. Chris Hillyer,CFOT/CFOS/I,
Master Instructor, Northern California Sound & Communication
JATC brought this to our attention.
you have an old cell phone, try it. Our experience is that older
cell phone cameras have better sensitivity at IR wavelengths
than newer phones, so you may want to toss that old flip phone
into the toolbox.
Ripley Fiber Stripper
recently sent us some new fiber strippers to try, the Ripley
Tri-hole fiber stripper model CFS-3. It is aimed at
contractors and installers and is very reasonable prived - plus
we understand there are some introductory price specials from
The CFS-3 can strip fiber jackets, 900 micron buffer and 250
micron buffer for one step cable preparation.
- 1st hole strips 1.6 – 3mm Fiber Jacket to the 600-900 buffer
- 2nd hole strips the 600-900 micron buffer coating to the 250
- 3rd hole strips the 250 micron buffer coating to the 125
micron glass fiber.
the CFS-3 on several fibers and cables and found it easy to use
and very consistent. It seemed much less sensitive to the angle
you hold it at when stripping fibers than some strippers like
this and it was very effective even stripping some older, more
more information on the Ripley CFS-3 Part #: 81300.
Introduces OLTS For MPO Connectors
One of the biggest problems with multifiber MPO connectors is
testing. Viavi Solutions (formerly JDSU) has introduced its
SmartClass Fiber MPOLx optical loss test set, a basic test
solution for cabling systems that utilize multi-fiber MPO
connectors. The testing of parallel optics with MPO connectors
has always been difficult for regular single or dual fiber OLTS,
needing MPO to SC or LC breakout cables for testing one fiber at
a time and using the three cable “0 dB” reference method. The
MPOLx should make testing cable plants using these connectors
The MPOLx can test for length, optical loss, polarity and
inspect fiber end-face condition - a complete cable plant test.
The ability to check polarity is important since there are
several polarity schemes used in MPO systems. The MPOLx is fast
too, delivering comprehensive test results in less than 6
seconds for all 12 fibers.
information on the Viavi MPOLx here.
YOKOGAWA OTDR Has Extended range, High Resolution And Multitasking
One OTDR manufacturer you don't hear as much about is YOKOGAWA
(formerly ANDO) which is too bad - they make some of the best
OTDRs, exemplified by this new model AQ7280. Need long range -
how about 50dB. High resolution - 0.6m dead zone. Like touch
screens, but for some functions want hard buttons, it's got
that. Options for VFL, microscope, light source and power meter,
etc. - it has that too.
But the unique aspect of the YOKOGAWA AQ7280 is it offers
multitasking - you can let do a trace with long averages while
you inspect connectors, make power readings, use the VFL or
info on the YOKOGAWA AQ7280.
thanks Yokogawa for a gift of an OTDR to use for R&D and
Recycling Communications Cable
contacted by a company that recycles electronics communications
equipment and cabling. CommuniCom recycles
for Telcos and CATVs. They also recycle Fiber Optic Cable and
associated Materials (the fiber scrap). And, they reclaim OSP
abandoned copper cables (abandoned from road moves or FTTx
growth). This is a huge part of our business. They do the work
(permitting/locates/labor) for free and we revenue share back
with our clients (telcos).
offers products for micro (or I guess they call it nano-)
trenching and their
website is very informative. They also have Kabel-X,
a method of extracting copper cables from old conduit. Both
websites are informative and interesting. Watch
this video on the cable removal process!
Protecting Pedestals From
and underground vaults can be damaged by rodents who come up
through the base and damage cables. Uraseal "Drain N'Seal"
foam deters mice from taking up residence in your pedestals. They
have some good videos on using their product.
Test Equipment – Buy or Sell
you read the FOA
pages on cleaning?
To Learn More About FTTx? Try our free online self-study
program at Fiber